XBURN Command-Line Manual

Version: X1482A Date: October 31, 2016Download PDF
VersionReleased
X1482AOct 31, 2016 download view

XBURN creates OTP images, and programs images into the OTP memory of xCORE devices.

Overall Options

The following options are used to specify the OTP image and security register contents.

  • xe-file

    Specifies bootable images to be constructed from the loadable segments fromxe-file and a default set of security bits.

  • otp-file

    Specifies the OTP segments from otp-file which includes the security register value.

  • --version

    -v

    Displays the version number and copyrights.

  • --help

    -h

    Prints a description of the supported command-line options.

Target Options

The following options are used to specify the target hardware platform.

  • --list-devices

    -l

    Prints an enumerated list of all JTAG adapters connected to the host and the devices on each JTAG chain, in the form:

    ID - NAME    (ADAPTER-SERIAL-NUMBER)

    The adapters are ordered by their serial numbers.

  • --id ID

    Specifies the adapter connected to the target hardware.

  • --adapter-id ADAPTER-SERIAL-NUMBER

    Specifies the serial number of the adapter connected to the target hardware.

  • --jtag-speed n

    Sets the divider for the JTAG clock to n. The corresponding JTAG clock speed is 6/(n+1)MHz. The default value is 0 (6MHz).

  • --spi-div n

    Sets the divider used in the AES Module for the SPI clock to n. The corresponding SPI clock speed is set to 100/(2n) MHz. The deafult value is 20 (2.5MHz).

    This option is only valid with --lock.

Security Options

  • --genkey keyfile

    Outputs to keyfile two 128-bit keys used for authentication and decrpytion. The keys are generated using the open-source library crypto++.

    This option is not valid with --burn or --lock.

  • --lock keyfile

    Specifies the XCORE AES boot module and adefault set of security bits.

Security Register Options

The following options are used to specify the contents of the OTP security register, overriding the default options for burning XE images, OTP images and the AES module, as given in the table below.

Default security bits written by XBURN

Security Bit

XE Image

OTP Image

AES Module (--lock)

OTP Boot

Enabled

As per OTP image file

Enabled

JTAG Access

Enabled

Disabled

Plink Access

Enabled

Enabled

Global Debug

Enabled

Disabled

Master Lock

Disabled

Enabled

Secure Config Access

Enabled

Enabled

  • --enable-otp-boot

    Enables boot from OTP.

  • --disable-jtag

    Disables JTAG access. Once disabled, it is not possible to gain debug access to the device or to read the OTP.

    This option does not disable boundary scan.

  • --disable-plink-access

    Disables access to the plink registers from other tiles. Disabling plink access restricts all access of the registers of each plinks to the tile local to that plink.

  • --disable-global-debug

    Prevents the device from participating in global debug. Disabling global debug prevents the tiles from entering debug using the global debug pin.

  • --enable-master-lock

    Enables the OTP master lock. No further modification of the OTP is permitted.

  • --disable-secure-config-access

    Disables access to the security config register.

Programming Options

By default, XBURN writes the specified OTP images to the target platform.

  • --force

    -f

    Do not prompt before writing the OTP. This is not default.

  • --outfile

    -o otp-file

    Place output in otp-file, disabling programming.

  • --make-exec xe-file

    Place an executable in xe-file that when run on an xCORE device performs the specified OTP burning operation; disables programming.

    The XE file can be run later using XRUN.

  • --target-file xn-file

    Specifies xn-file as the target platform.

  • --target platform

    Specifies a target platform. The platform configuration must be specified in the fileplatform.xn, which is searched for in the paths specified by the XCC_DEVICE_PATHenvironment variable (see XCC_DEVICE_PATH).

  • --read

    Prints the entire contents of the OTP.

  • --size-limit n

    Limits the amounts of OTP memory written to the first n bytes of the OTP. If the image doesn’t fit within the specified limit an error will be given.

  • --mac-address mac

    Writes a MAC address to the end of the OTP. The MAC address should be specified in the form 12:34:56:78:9A:BC. Multiple MAC addresses can be written by specifying the --mac-address option multiple times. MAC addresses are written to the OTP in the order the options appear.

  • --serial-number serial

    Writes a 32-bit serial number to the end of the OTP.

  • --no-compression

    Prevents XBURN from compressing all binary data.

  • --no-compression-validation

    Prevents XBURN from validating the decompression algorithm within XSIM.

Documentation